Finish by cutting and installing panels of wire.Are cost-friendly compared to a wood fence. Stapling directly behind a vertical wire will help keep the fencing taught as you move down the line. Start stapling down the line and pulling out the slack. Ideally with help, hold the fencing halfway up the top bar and halfway down the bottom support. For each section, I measured the outside length and cut the wire to the specified length prior to installing. We had our rolled fencing laid out flat overnight prior to installation. The wire fencing should be rolled out the length of your fencing run and straightened out. Step 6 – Roll Out and Staple in Wire Fencing Finally, finish by screwing in 2 deck screws on each side of the support down the line of fence posts. If your working alone, consider starting one screw on each side of the 2”x4” as this will help when installing. Next, measure and cut the inside width between each post and drill angled pilot holes prior to placing in the support. Keeping the bottom 2”x4” support off the ground will help prevent standing water from being directly on the wood. This is where you will tie in the top of the bottom support.
HOG WIRE FENCE FOR DECKS INSTALL
Step 5 – Install the Bottom Supportįirst, measure and mark 36” from the top bar down the fence post. Be sure to drill pilot holes before screwing in the deck screws to prevent the lumbar from splitting. When tying two top bars together, screw in the end of one to halfway across of the 4”x4” post and start the next on the other half. Measure and cut your 2”x4” to the necessary length. Now that we have the fence posts set, it’s time to install the top bar. Also, being a wire fence, it will not have a large wind load so we were not too concerned with the adding concrete in order to stabilize the structure. Q: Should I use concrete? A: We chose not to because concrete can create a shelf for water to sit up against the fence post and speed up wood rot. Depending on the grade of the area you may need to dig the holes deeper (or cut the post shallower) to make the fence level, just be sure to have a minimum of 12” of wood buried in the soil for stability. Make sure to level each post off the one before it rather than the entire line of posts. You can do this simply with your foot, the end of the level, or the back end of a shovel, whatever works to get that soil packed tight! Repeat the process and move down the fence line. It is very important to tightly pack the soil around the post to ensure the posts do not move later on. Making sure the post is plumb, start to fill and pack dirt around the post. Place a few inches of gravel underneath the post and around the base (this will help with drainage and prolong the life of your fence). Using a pencil, mark 42” on the post to mark how deep to bury the post. Again, in our climate we planned to bury 12” and have 42” showing, so adjust accordingly.
Once your holes are dug, cut the posts to 54”.
HOG WIRE FENCE FOR DECKS MANUAL
If you’re going to use a manual post hole digger, I would also recommend a post hole shovel to widen the sides or break up the clay soil as needed.
Me, being the cheap-o, used a manual post hole digger to dig through our rock hard clay soil and greatly regretted that the next day at work. Depending on your soil, this is where spending the money to rent a gas-powered auger will save you a lot of time and sore muscles. Now using a post hole digger you’re going to want to dig those holes to about 14” to 18” deep and 8” wide. If your gate is too big you may potentially have sagging issues later on. We chose to do a 36” gate because it is a great size for moving a wheelbarrow or lawnmower in and out. We found it easiest to start by marking your gate location and continue to mark your fence posts off of it. Four-foot spacing is ideal but does not have to be exact as you will be attaching the hog wire to the backside of the fence.
HOG WIRE FENCE FOR DECKS FREE
We used marking paint for this but feel free to use stakes, flags, or simply dig a small hole. Measure and mark the locations of your post holes. You will, of course, want to customize this fence to suit your needs but this tutorial will give you a head start for getting your new fence in the ground. This whole project can be completed in a day or two (depending on your skill level and extra help) and costs less than $300*. We give you a list of the necessary tools, along with a shopping list for 50 feet of fence. This guide will break down the steps to creating a simple garden fence using hog wire. The benefits of this fence are that you can see through it and it also gives you the ability to grow vining plants up it during the growing season. We have always loved the look of cattle or livestock style fencing, (we assume you do too if you are reading this), so we decided to include this style in our garden plans. By clicking these links and making a purchase we do receive a small portion of that sale, at no extra cost to you! This allows us to continue bringing you content.
0 kommentar(er)
